Just How To Install A Bath Tub (For Novices).
Just How To Install A Bath Tub (For Novices).
Blog Article
They are making several great points on How to Install a Bathtub Yourself in general in this post further down.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open up a wall to get rid of the old bathtub as well as place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub as well as set in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. Instead of employing a contractor to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This post will assist you mount a new bath tub in your restroom if you have actually already purchased a brand-new tub as well as don't require to change the plan of your previous water supply pipes.
Your devices and material list must comprise the following:
Preparing for the Setup
To start with, the supporting structure supplied with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to stop pressure on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, position the bathtub in the called for position. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub till the spirit level reviews level.
To mount faucets, fit the bottom of the furthest versatile tap port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the water as well as examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally examine the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been made use of at least when as this will certainly settle it right into its last position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers are in location in between the faucet and the sink. Secure the tap in position with the maker given backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog entry about How to Install a Bathtub Yourself when doing a search on the web. Those who liked our page kindly do not forget to pass it around. Thank you for your time. Kindly check our website back soon.
Get An Estimate Report this page